ICM Controls ICM300C Heat Pump Defrost Control Board, 18 - 30 VAC Input, 1 amp Output

• Ultra low cost
• Pin-for-pin compatible with OEM type 621 controls
• Simple time and temperature control
• Must have external relays for fan, reversing valve and auxiliary heat
• High installed base

Sid Harvey Item #:ICM300C: Replaces Part #:'s : B12260-06,
,

ICM Controls ICM283 Hot Surface Universal Gas Ignition Control Module for Gas-Fired Furnaces, Boilers and Other Heating Applications, 120 and 24 VAC

• Low cost, direct replacement ignition control
• Single/dual rod sensing capabilities
• Switch selectable lockout times, ignition trials
• Works with both Natural and LP gas systems
• Diagnostic LED to aid in troubleshooting

Sid Harvey Item #:ICM283: Replaces Part #:'s : H5780,
,

ICM Controls ICM291 Ignition Module Pre-Purge: 45 seconds Trial for Ignition: 5+2 seconds,
,

ICM Controls ICM402 Line Monitor, 190 - 600 VAC , SPDT - NO

• Low cost 3 PH protection for single side
• Monitors for phase reversal, phase loss, unbalance % as a function of input VAC age
• Bright LED indicators for ON and FAULT
• 115, 208/230 VAC control VAC age input
• Epoxy encapsulated for moisture protection
• Easy to install, no adjustment
• Less than 1 sec phase loss response
• Automatic reset from a fault condition
• Compact packaging - fits almost anywhere
• Works great with the ICM450 for load side monitoring of part winding start motors and multiple compressor systems

,
,

The ICM492 constantly monitors line VAC age and protects single-phase equipment against low and high VAC age conditions, and rapid short cycling due to VAC age fault or power interruption. Its easy-view, backlit digital display makes it user friendly to read and monitor VAC age conditions, and adjust parameters to meet specific needs.

• Protects against over and under VAC age and rapid short cycling caused by transient faults and power interruptions
• Easy view, backlit digital display
• RMS VAC age set point
• Adjustable VAC age set point
• Adjustable over VAC age setting
• Adjustable under VAC age setting
• Adjustable anti-short cycle time delay
• Adjustable response time
• Control mode
• Universal line VAC age input
• Heavy duty SPDT relay output
• Universal control VAC age input (for integrating a thermostat)

Sid Harvey Item #:ICM492C: Replaces Part #:'s : DSP-1,
,

ICM Controls ICM450A Line Voltage Monitor, Manual or Automatic Reset,
,

ICM Controls ICM493 Line VAC age Monitor with Built-In Surge Suppression, An advanced, single phase line VAC age monitor with a bank of surge arresters for added protection against lightning strikes. Includes a built-in 40A contactor. Ideal for Mini-Splits or other valuable, single phase equipment. Protects against over and under VAC age, rapid short cycling caused by transients, and high-power surges. Easy to view, backlit digital display. NEMA-rated 3R enclosure for outdoor use, Easy installation and setup.,
,

ICM Controls ICM220 Lockout Relay, 18 - 30 VAC, SPDT,
,

ICM Controls ICM870-32AMotor Starter Soft Start

ICM Controls FS1500L Non-Programmable Garage Thermostat

• 1 Heat 24 Vac 35-75 Degrees
  Frost Sentry Garage Thermostat
  This easy-to-operate garage thermostat allows you to maintain temperature to your garage/storage area. Attractive, extra-rugged, highly reliable and accurate, this thermostat will look and perform like new for years to come. Ideal for garages, warehouse, storage facilities, etc
  

ICM Controls SC2010L Non-Programmable Thermostat 1 H/1 C 1 Heat Pump 24 VAC 45-90 Deg

ICM Controls SC2010L