S2K Commerce - Products Dropdown
ActionsS2K Commerce - Shopping Cart
ActionsS2K Commerce - Order Entry
ActionsDanfoss 013G8019 Nickel-Plated Brass Thermostatic Radiator Angle Valve,Sid Harvey Item #:013G8019: Replaces Part #:'s : 5838,
Item#:
013G8019
Manufacturer Item:
013G-8019
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss 013G8250 Non-Electric Operator,
,
,
Item#:
013G8250
Manufacturer Item:
013G-8250
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Item#:
030G6440
Manufacturer Item:
030G6440
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Mars 060G1037 Pressure Transmitter
,
,
,
,
Item#:
060G1037
Manufacturer Item:
060G1037
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss HCZC0150UWF300N Refrigeration Condensing Unit 1-1/5 HP 230/1 Medium/High Temperature,
,
,
Item#:
HCZC0150UWF300N
Manufacturer Item:
114N6401
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss 013G8562 Remote Sensor Wall Mount (Non-Electrical) 6' Cap,
,
,
Item#:
013G8562
Manufacturer Item:
013G-8562
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss 117U5023 Start Capacitor
- 240 MFD 125 VAC,
,
Item#:
117U5023
Manufacturer Item:
117U5023
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss 013G8024 Nickel-Plated Brass Thermostatic Radiator Angle Valve, 1", FPT x MPT Union Tailpiece
,
,
- Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
- Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
- EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
- Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
- Valves remain normally open with no operator mounted
- Brass bonnet, spindle, nickel-plated tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring
,
,
Item#:
013G8024
Manufacturer Item:
013G8024
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Danfoss 013G8020 Thermostatic Radiator Straight 3/4" Nickel-Plated Brass,
,
,
Item#:
013G8020
Manufacturer Item:
013G-8020
Manufacturer:
DANFOSS MANUFACTURING CO LTD