• More efficient both starting and running
• More reliable
• Auto reset thermal overload
• Quiet sealed ball bearings
• Eliminates centrifuGallon start switch
• More versatile
• Replace 1/15 to 1/4 HP motors
• Replaceable capacitor
• Capacitor 9 location (looking from rear)
• Requires 14 mfd capacitor
• 10" lead length

• More efficient both starting and running
• More reliable
• Auto reset thermal overload
• Quiet sealed ball bearings
• Eliminates centrifuGallon start switch
• More versatile
• Replace 1/15 to 1/4 HP motors
• Replaceable capacitor
• Capacitor 9 location (looking from rear)
• Requires 16 mfd capacitor
• 10" lead length

Carlin Motors 98022S

,

• Interrupted duty ignition
• Recycle on flame failure
• Serviceman reset protection (latch-up after 3-consecutive lockouts)
• Diagnostic LED
• 15 sec trial for ignition (TFI) other timings available
• 1.3 sec flame failure response time (FFRT)
• Alarm contacts
• Thermostat/aquastat compatible
• SMC (safety monitoring circuit) technology

• Interrupted duty ignition for high efficiency
• SMC technology for safety monitoring
• LED indicators, alarm contacts and pump prime for economic as well as efficient performance
• Serviceman reset protection ( latch-up after three consecutive lockouts)
• 15 sec trial for ignition (TFI) other timings available
• It offers recycle on flame failure and 1.3 sec flame failure response time
• Oil primary control has a input voltage rating of 120 VAC, input frequency rating of 60 Hz and input power rating of 9 VA
• It has a temperature rating of 32 - 140 deg F, resistive rating of 1500 ohm and safety switch timing of 15 sec
• Primary control offers serviceman reset protection and valve delay on/motor delay off feature
• It has a motor load of 10 FLA/60 LRA, ignitor load of 120 VAC at 60 Hz and valve load of 120 VAC at 60 Hz
• 500 VA motor load
• 24 VAC/VDC, 2 amp alarm contacts
• Flame signal test jack

• Interrupted duty ignition
• 15 sec trial for Ignition 40200 (1.3 sec flame failure response time (FFRT))
• Recycle on flame failure
• Thermostat/aquastat compatible
• SMC (safety monitoring circuit) technology

• Interrupted duty ignition
• Recycle on flame failure
• Serviceman reset protection (latch-up after 3-consecutive lockouts)
• Diagnostic LED
• Valve delay on/motor delay off (pre/post-purge)
• 15 sec trial for ignition (TFI) other timings available
• 1.3 sec flame failure response time (FFRT)
• Alarm contacts
• Thermostat/aquastat compatible
• SMC (safety monitoring circuit) technology

• Interrupted duty ignition for high efficiency
• SMC technology for safety monitoring
• Diagnostic LED indicators
• Secondary burner control has a input voltage rating of 120 VAC, input frequency rating of 60 Hz and input power rating of 10 VA from limit circuit
• 15 sec trial for Ignition 40200 (1.3 sec flame failure response time (FFRT))
• 30 sec trial for Ignition 42230 (1.3 sec flame failure response time (FFRT)
• Recycle on flame failure
• It has a temperature rating of 32 - 140 deg F and resistive rating of 1500 ohm
• Valve delay on/motor delay off for economic as well as efficient performance
• It has a motor load of 10 FLA/60 LRA and ignitor load of 120 VAC at 60 Hz
• 500 VA motor load

• Programmable, micro-processor based, universal replacement for CAD cell oil burner primary controls
• Replaces Carlin, Beckett, Honeywell and ICM primary controls
• On-board LCD screen no special tool needed
• Valve delay on (0, 3, 10, 15, 30, 60, 120)
• Trial for ignition time (15, 30, 45)
• Motor delay off (0, 10, 15, 30, 120, 300, 900)
• Interrupted or intermittent duty operation
• Early spark termination timing (0, -5, -10)
• Number of recycles (0, 3)
• Serviceman reset protection
• Blocked vent protection
• Alarm contacts
• Built-in pump prime
• Fault history

• 45 sec trial for ignition
• Red LED lockout indicator
• Thermostat/aquastat compatible SMC (safety monitoring circuit) technology
• 5 amp full load, 60 amp locked rotor motor load
• 120 VAC, 60 Hz, 500 VA igniter load

carlin parts r75-47

,
,