Tjernlund 950-0012 Sensing Tube for HSJ HS1 & GPAK Series Gas Sidewall Power Venter Fan

950-0012

950-0012

Tjernlund 950-1040 Relay Kit GPAK-J,GPAK-1,HS-3,HS-4
,
,

950-1040

950-1040

Tjernlund HS2 Aluminized Steel Housing and Blower Wheel Side Wall Power Venter, 6", 115 VAC , 3300 RPM , 600000 BTU

• UC1 universal control and a diaphragm fan proving switch safety interlock which will shut down the heating equipment if a venting malfunction occurs
• Built-in adjustable damper also allows regulation for maximum combustion efficiency
• Interlocks with any 24/120 VAC burner circuit
• UC1 universal control features adjustable pre/post-purge, LED status indicators, and fault code memory
• Thermal protection, sintered iron sleeve type bearing
• UC1 interlock control, fan proving switch, adjustable damper, vibration isolators included

Sid Harvey Item #:HS2: Replaces Part #:'s : 30933,
,

Tjernlund HS2

Tjernlund HS2

Tjernlund HS1 Steel Side Wall Power Venter with UC1 Control, 115 VAC at 60 Used for side wall venting residential/light commercial natural gas, LP or oil fired equipment including: Furnaces, boilers, water heaters and unit heaters. All models feature the new UC1 universal control and a diaphragm fan proving switch safety interlock which will shut down the heating equipment if a venting malfunction occurs. Built-in adjustable damper also allows regulation for maximum combustion efficiency. UC1 universal control features include, adjustable pre and post-purge settings, LED status/diagnostic indicators, fan prover switch monitoring. Interlocks with any 24 - 120 VAC burner control circuit and also includes dry contact actuation option. Easily interlock multiple appliances with our MAC-series multiple appliance controls.Sid Harvey Item #:HS1: Replaces Part #:'s : 21767,

,

Tjernlund HS1

Tjernlund HS1

Tjernlund The SideShot models SS1 and SS2 SideWall Vent Systems include the UC1 Universal Control for increased safety, performance and reliability. Designed for oil fired heating equipment or a deluxe gas vent system. Patented vent termination propels flue gases at high velocities away from the building exterior, a necessity when venting oil fired equipment. Both models can be installed with zero clearance to combustible materials and have stainless steel construction in critical areas. Factory wired safety and operating controls allow simple interlock with any burner. The new model SS2 features a self-cleaning stainless steel, backward inclined impeller and sealed ball bearing motor for virtually maintenance free installations. Ultra-fine draft adjustment and slide-out access to all internal components. Easy multiple appliance interlocks with our MAC Series multiple appliance controls.

• Use to side wall vent non-condensing oil fired boilers, water heaters and furnaces that otherwise would require a conventional roof top terminated chimney
• Built-in interlock control with redundant high limit safety switch interfaces easily with thermostat, aquastat or primary controls
• Adjustable pre and post purge timing and easy fault code retrieval
• Stainless steel construction in all critical components including outdoor terminus
• Patented design jets flue gases away from the outside wall to eliminate potential staining of siding
• Slide out service drawer and material handling stainless steel impeller

Sid Harvey Item #:SS2: Replaces Part #:'s : 6H167A,
,

Tjernlund SS2

Tjernlund SS2

Tjernlund UC1 Control Board,
,

tjernlund uc1

tjernlund uc1

Tjernlund WHKE Millivolt Interlocking Switch MAC1qE/MAC4E,
,

tjernlund whke

tjernlund whke

Tjernlund DB-2-6 Galvanized Steel Housing Inline Duct Booster Fan

• Drip proof - non ventilated thermal protection
• The DB-2 duct booster is designed to increase the flow of heated air in warm air heating systems or cooled air in central air conditioning systems
• The duct booster can be mounted on round or flat ducts
• 120 VAC
• 0.51 AMP
• 200 CFM
• 1550 RPM

Replaces Part #:'s : x89-411,
,

104-11

104-11