Sid Harvey Remanufactured P90-40R

Sid Harvey Remanufactured P9-22R

Sid Harvey Remanufactured R75-50R

• Provide intermediate switching of a line voltage device from a low voltage controller
• Integral transformer provides low voltage power for control circuit
• Includes enclosure
• Contact rating: 10.2 amp at 120 VAC, 5.1 amp at 240 VAC full load; 61.2 amp at 120 VAC, 30.6 amp at 240 VAC locked rotor; 10 amp at 120 VAC, 6 amp at 240 VAC resistive Honeywell RA89A1074 Switching Relay, 120 volt Input, 24 VAC Coil at 50/60 Hz, 0.4 amp Coil, SPST
  

  Sid Harvey Remanufactured R510-15R

Interrupted ignition type
• Combine a Protectorelar unit for cycling the burner and a Pyrostat flame detector for sensing temperature changes of flue gases up to 1000 deg F
• Manual reset of safety switch required after ignition failure completely shuts off main burner
• Include manual trip safety switch to assure burner shutdown during servicing
• Mount with flange for mounting on curved or flat surfaces
• Works with 2-wire and 3-wire 24 VAC thermostat
• 2 years warranty
  Sid Harvey Remanufactured R20R
  

  Sid Harvey Remanufactured R20R

• Intermittent ignition kwik-sensor CAD cell relays on oil burner systems with 15, 30 or 45 sec safety timing
• Certain types have unique signal-light feature with glows whenever safety lock-out occurs
• Line voltage safety switch eliminates burner run-on in the event that the motor relay contacts weld closed
• Solid state flame detection circuitry is not affected by vibration or high or low ambient temperatures
• Recycles on momentary flame failure or power interruption
• 4 x 4 Inch junction box, 10 Inch leads mounting
• 2 wire thermostat
• 0.4 amp thermostat anticipator setting
• Safety lock-out lamp White Rodgers Cooling Controls 668-401 Gray Metal Enclosure Kwik-Sensor CAD Cell Relay, 120 VAC, 45 sec
  

  Sid Harvey Remanufactured R79-6R

Sid Harvey Remanufactured R75-41R

• Uses rectification principle of electronic flame detection
• Primary control provides solid state, electronic flame safeguard protection for industrial and commercial single or dual fuel burners for rectification type flame detection
• Recycles if flame signal lost while in run, failure to establish pilot results in a lockout
• Safe-start check prevents start-up if flame-simulating failure occurs in flame detector circuit
• Includes built-in protection against ignition crossover in flame rod systems
• Solid state circuitry
• Mounts and removes easily through use of captive mounting screws
• Mounting base is made of strong thermoplastic
• Includes SPDT alarm contacts Honeywell Protectorelay RA890F1288 Flame Safeguard Primary Control, 120 VAC at 50/60 Hz, SPDT
  

  Sid Harvey Remanufactured R202-52R

Sid Harvey Remanufactured R75-29R

Sid Harvey Remanufactured R80-32R

• Provide intermediate switching of a line voltage device from a low voltage controller
• Integral transformer provides low voltage power for control circuit
• Includes enclosure
• Contact rating: 7.4 amp at 120 VAC, 3.7 amp at 240 VAC full load; 44.4 amp at 120 VAC, 22.2 amp at 240 VAC locked rotor; 10 amp at 120 VAC, 6 amp at 240 VAC resistive; 2000 VA (120 - 240 VAC); secondary DC - 1 amp at 12 VDC, secondary millivolt - 300 milli-amp at 750 MV Honeywell RA832A1066 Switching Relay with Internal Transformer, 120 volt Input, 24 VAC Coil at 50/60 Hz, 0.4 amp Coil, DPST
  

  Sid Harvey Remanufactured R520-26R

Sid Harvey Remanufactured R176-6R