S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Danfoss MTZ36-4VI Hermetic Refrigeration Compressor 36000 BTU 460 VAC 3 HP,
,
,
Item#:
MTZ36-4VI
Manufacturer Item:
MTZ36-4VI
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss MTZ64-3VI Hermetic Refrigeration Compressor
- 5-1/2 HP 230 VAC
- POE Oil
- POE, R404A, R407C, R134A
- 1-3/4" RL - 7/8" x 1-1/4" RL - 3/4",
- 1-3/4" RL - 7/8" x 1-1/4" RL - 3/4",
- POE, R404A, R407C, R134A
- POE Oil
Item#:
MTZ64-3VI
Manufacturer Item:
MTZ64HM3AVE
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss 195B0586 Refrigeration Compressor R134A 115/1 Low Temperature,
,
,
Item#:
195B0586
Manufacturer Item:
195B0586
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss Hermetic Refrigeration Compressor
8153011 Adaptor
8156009 Gasket Gasket set, 1", 1-1/4", 1-3/4", OSG gaskets black and white
8156131 Gasket 1-1/4"
120Z0575 Acoustic hood for one-cylinder compressor
8153007 Solder sleeve, P06 (1" rotolock, 1/2" ODF)
8156001 Mounting Kit
7750009 Discharge thermostat kit
8156130 Gasket 1"
7703005 Valve set, V09 (1-1/4"~5/8"), V06 (1"~1/2"), Service kit
- 2 HP 208/230 VAC R134A, R404A, R407C, R407F, R507A
8153011 Adaptor
8156009 Gasket Gasket set, 1", 1-1/4", 1-3/4", OSG gaskets black and white
8156131 Gasket 1-1/4"
120Z0575 Acoustic hood for one-cylinder compressor
8153007 Solder sleeve, P06 (1" rotolock, 1/2" ODF)
8156001 Mounting Kit
7750009 Discharge thermostat kit
8156130 Gasket 1"
7703005 Valve set, V09 (1-1/4"~5/8"), V06 (1"~1/2"), Service kit
Item#:
MTZ22-1VI
Manufacturer Item:
MTZ22JC1BVE
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss 013G8015 Nickel-Plated Brass Straight Thermostatic Radiator Valve Body, 1/2", FPT x MPT Union Tailpiece
,
- Valve bodies are designed to meet the demands of the residential, commercial and industrial sectors
- Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
- Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
- EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
- Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
- Valves remain normally open with no operator mounted
- Brass bonnet, spindle, nickel-plated brass tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring
,
Item#:
013G8015
Manufacturer Item:
013G8015
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss 023Z8261 Liquid Line Filter Drier 1/4" OD
Applications:
Traditional refrigeration
Air conditioning units
Transport refrigeration
Danfoss 060-5233 Low Pressure Control 36" Cap W/1/4" Flare Nut Auto Reset
,
,
Item#:
060-5233
Manufacturer Item:
KPU1
Manufacturer:
DANFOSS LLC(HVAC/R)
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Danfoss 060B017066 Oil Pressure Control 4-65 lb 45 Second Time Delay,
,
,
Item#:
060B017066
Manufacturer Item:
060B017066
Manufacturer:
DANFOSS LLC(HVAC/R)
Danfoss HCZC0200UWF300N Air Cooled Condensing Unit, 2 hp, 14286 BTU/hr at 20 deg F, 22434 BTU/hr at 45 deg F, 230 VAC, R-404A, R-134A, R-507, R-407C
- Includes: electrical box, receiver, dual pressure control, fan cycling control, dual fan units larger than 3 hp use KPU fan cycling control, filter drier, sight glass, solenoid valve with coil
- Condenser designed for dependable performance in the toughest of high ambient conditions
- Easy access service valves on all units
- Universal high/medium/low range in R-404A fractional units
- Compact design
- 100% Factory tested
- Quiet, efficient hermetic compressors, factory mounted and factory wired
- Base mounted service valves with access port
- Durable 14 ga painted steel base plate
- Metal fan shroud and guard
- Self-regulating PTC crank case heater on 1-1/2 hp and above
- Lifting slots for easy and safe handling
- Versions available for indoor and outdoor applications
- Compressor sight glass on 1-1/2 hp and above
- Receiver with liquid shut-off, and fusible plug standard on all units
- Single fan
- MTZ22 hermetic compressor
- Complies with California standards
- Medium back pressure
Item#:
HCZC0200UWF300N
Manufacturer Item:
114N6404
Manufacturer:
DANFOSS LLC(HVAC/R)
Item#:
LJZM0200UWH000Q
Manufacturer Item:
114N3480
Manufacturer:
DANFOSS LLC(HVAC/R)