Tjernlund DJ-3 In-line Induced Draft Blower for Smokepipe and Aids Proper Exhaust of Combustion Gas, 115 VAC , 1/70 HP, 1550 RPM

• Thermal protected
• Aluminized steel blower wheel

Sid Harvey Item #:106: Replaces Part #:'s : 17140,
,

Tjernlund 100-12

Tjernlund PS1505 Fan Prover has been designed to monitor the pressure within the fan housing only. A motor or wheel failure will decrease housing pressure and deactivate the pressure switch, thus preventing combustion.

• Simple installation
• Mounting hardware furnished
• Fixed setpoints
• Voltage - 125 VA pilot duty at 24 VAC, 300 VA pilot duty at 115 - 277 VAC, 15 amp non-inductive to 277 VAC
• Electric switch: SPST, normally open snap acting contacts
• Electric connectors #6-32 screw terminals with cup washer
• Control setpoint non-adjustable
• Operating pressure, on increasing vacuum pressure rise, 0.05 plus or minus 0.02 Inch WC with diaphragm in vertical position
• 1/2 psi maximum pressure
• -400 to 1900 deg F Operating temperature
• Diaphragm vertical mounting position
• 5-1/2 Inch across mounting bracket

,
,

Tigerloop S220-9

Tjernlund 106-3 In-Line Draft Inducer 14" 14-3/4" W x 17" H x 10" D,
,

Thermo Products Inducer Motor AOPS7427

Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HP

• Venturi action starts air moving up the stack instantly and keeps it moving smoothly
• In-line inducers are built for long-lasting, trouble-free service
• Vari-draft control permits adjustment to individual job requirements
• Vents/chimneys utilizing in-line draft inducers must be vertically terminated above the roof line
• Solves venting problems: Undersized chimneys, negative pressures, long horizontal vent connectors, down drafts, cold equipment starts, restrictive heat exchangers/combustion chambers
• 1 year warranty Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HPSid Harvey Item #:106-1: Replaces Part #:'s : x89-444,
  
  ,
  
  
  
  

  Tjernlund 106

Tjernlund I Inline Draft Inducer, 115 VAC , 1/4 HP, 1725 RPM

,
,

Tjernlund 106-10

Tjernlund Specially designed to terminate Tjernlund Side Wall Vent Systems. They are also an approved method of terminating many horizontally vented appliances. Vent hoods feature heavy duty, corrosion resistant aluminum construction. Models VH1-3, 4 and 6 also have an additional heat shield for built in clearances from combustibles. Building exteriors are kept clean while the aesthetics of the structure remain undisturbed. All mounting hardware is included.

• 8" square rough-in
• Mounting hardware

Sid Harvey Item #:106-20: Replaces Part #:'s : x89-442,
,

Tjernlund 106-2

Tjernlund Specially designed to terminate Tjernlund Side Wall Vent Systems. They are also an approved method of terminating many horizontally vented appliances. Vent hoods feature heavy duty, corrosion resistant aluminum construction. Models VH1-3, 4 and 6 also have an additional heat shield for built in clearances from combustibles. Building exteriors are kept clean while the aesthetics of the structure remain undisturbed. All mounting hardware is included.

• 9" rough-in diameter
• Mounting hardware

Sid Harvey Item #:106-21: Replaces Part #:'s : x81-965,
,

Tjernlund 106-20

Tjernlund The SideShot models SS1 and SS2 SideWall Vent Systems include the UC1 Universal Control for increased safety, performance and reliability. Designed for oil fired heating equipment or a deluxe gas vent system. Patented vent termination propels flue gases at high velocities away from the building exterior, a necessity when venting oil fired equipment. Both models can be installed with zero clearance to combustible materials and have stainless steel construction in critical areas. Factory wired safety and operating controls allow simple interlock with any burner. The new model SS2 features a self-cleaning stainless steel, backward inclined impeller and sealed ball bearing motor for virtually maintenance free installations. Ultra-fine draft adjustment and slide-out access to all internal components. Easy multiple appliance interlocks with our MAC Series multiple appliance controls.

• Use to side wall vent non-condensing oil fired boilers, water heaters and furnaces that otherwise would require a conventional roof top terminated chimney
• Built-in interlock control with redundant high limit safety switch interfaces easily with thermostat, aquastat or primary controls
• Adjustable pre and post purge timing and easy fault code retrieval
• Stainless steel construction in all critical components including outdoor terminus
• Patented design jets flue gases away from the outside wall to eliminate potential staining of siding

Sid Harvey Item #:106-10: Replaces Part #:'s : 6H167,
,

Tjernlund 106-1

Tjernlund 950-0800 Head Cooling Fan Motor 460 VAC

Tjernlund Motor 950-0800

Tjernlund 950-0640 High Limit Switch SS-1,
,

Thermo Products Heating Parts 350989

Tjernlund 950-0650 Fan Prover Kit SS-1,
,

Tjernlund 950-0030

Tjernlund 950-0625 Motor with Wheel Kit

,
,

Tjernlund Motor 950-0015